What does the model describe?
Surface tension is energy per new interface area or tangential force per length. Curved interfaces support pressure jumps, causing liquid to rise or fall in narrow capillaries.[1]
Surface tension is energy per new interface area or tangential force per length. Curved interfaces support pressure jumps, causing liquid to rise or fall in narrow capillaries.
Young–Laplace uses both signed principal curvatures. A spherical drop with one interface has Δp=2γ/R. A thin soap bubble has two interfaces and approximately 4γ/R. Radius must not be confused with diameter.[1]
Assumptions, quantities and limits
Capillary height h concerns static liquid in a narrow circular tube of radius r, with constant contact angle θ measured through the liquid and constant γ, ρ, g. Gas density, meniscus volume and hysteresis are neglected.[1]
- surface tension (N/m)
- capillary radius (m)
- contact angle through the liquid (rad)
- signed capillary height (m)
Reasoning step by step
Capillary height h concerns static liquid in a narrow circular tube of radius r, with constant contact angle θ measured through the liquid and constant γ, ρ, g. Gas density, meniscus volume and hysteresis are neglected.[1]
Vertical interfacial force around the circumference is 2πrγcosθ, and column weight is ρgπr2h. Balancing yields h=2γcosθ/(ρgr). At θ>90°, cosθ is negative, giving capillary depression.[1]
N/m equals J/m2. Temperature, contamination and surfactants can change γ. A value inferred from one capillary height therefore also depends on contact angle and tube geometry, not just the liquid name.[1]
Young–Laplace uses both signed principal curvatures. A spherical drop with one interface has Δp=2γ/R. A thin soap bubble has two interfaces and approximately 4γ/R. Radius must not be confused with diameter.[1]
Two fully worked examples
Complete wetting
- Given
- γ=0.072 N/m, ρ=1000 kg/m3, g=10 m/s2, r=1 mm, θ=0.
- Find
- Find capillary height.
Balance force and weight.
Insert radius in metres.
Result: h=14.4 mm.
Check: Circumference force≈0.000452 N matches column weight≈0.000452 N.
Drop and soap bubble
- Given
- γ=0.030 N/m, R=2 mm.
- Find
- Compare pressure jumps.
One interface for the drop.
Two interfaces for a thin bubble.
Result: 30 Pa for the drop model,60 Pa for the thin soap bubble.
Check: Both double if radius halves.
Recall the method later with the formula’s flashcards.
10 flashcards · English materials
Already have an account? Sign in for flashcardsAvailable from Essential. A ready-made formula set, no AI credits required. Article exercises are not all included.
What surface tension do common liquids have?
Surface tension is a measured material property. It depends on temperature and on how clean the surface is; soap in water lowers it markedly. The textbook values below apply at 20 °C unless another temperature is given. If a problem states a different value, use that one.[1]
- Water at 0 °C:
- Water at 20 °C:
- Water at 100 °C:
- Soapy water, typical:
- Glycerin:
- Ethyl alcohol:
- Mercury:
Capillary height also depends on the contact angle θ between liquid and wall. Typical values are 0° for water, ethyl alcohol and most organic liquids on clean glass, 26° for kerosene on glass, 90° for water on silver, 107° for water on paraffin and 140° for mercury on glass. Below 90° the liquid rises, at 90° the level stays the same, and above 90° it drops.[1]
Five exercises with solutions and learning goals
Calculate · Foundation
Halve r with other values fixed: h?
Show hint
Inverse proportionality.
Learning goal: Check physical assumptions and calculation steps together.
Show solution and calculation
h doubles.
Rearrange · Foundation
θ=90°: h?
Show hint
Contact angle.
Learning goal: Check physical assumptions and calculation steps together.
Show solution and calculation
cos90°=0, so h=0 in the model.
Interpret · Application
Why can h be negative?
Show hint
Signed angular factor.
Learning goal: Check physical assumptions and calculation steps together.
Show solution and calculation
At θ>90° the vertical interfacial force points down; cosθ<0.
Error analysis · Application
Does every drop have 4γ/R?
Show hint
Count interfaces.
Learning goal: Check physical assumptions and calculation steps together.
Show solution and calculation
No.
A drop has one interface and 2γ/R;4γ/R belongs to a thin soap bubble with two interfaces.
Transfer · Challenge
How does surface energy change for twice the new area?
Show hint
Keep γ constant.
Learning goal: Check physical assumptions and calculation steps together.
Show solution and calculation
At fixed γ, ΔE=γΔA doubles.
Check your understanding with the formula’s reference test.
8 test questions · English materials
Already have an account? Sign in for the testAvailable from Essential. A ready-made formula set, no AI credits required. Article exercises are not all included.
Connections and further study
Continue with Hydrostatic pressure, Pressure, Buoyant Force (Archimedes).
Sources for this explanation
Quanta · Updated November 6, 2026
Editorial responsibility: Quanta Study editorial team
Review scope
This explanation, 2 worked examples and 5 exercises are available in German and English. Structure, source references and mathematical notation undergo automated checks. Calculations, model assumptions and both language versions receive a separate AI review.
An independent, named human subject review has not yet been documented. Our exercise numbers are worked examples, rather than measurements published by the cited sources.
Editorial responsibility, sources and methodsChange history
- Authored the DE/EN model with assumptions, original examples, five solved exercises and subject links.
Cite this reference page
Quanta. Surface tension and capillarity. Updated November 6, 2026. https://quanta-study.de/en/formula-sheet/oberflaechenspannung-kapillaritaet
When citing a specific scientific statement, also cite the specialist source linked to that statement.